Fibre Optic Bundles If Light example essay topic

Fiber OpticsAssignmentMany modern medical materials and equipment work on a principle which is beyond the capacity of human transducers. Comment and discuss the working principles of an endoscope, a recto scope showing the illuminating path, the image path, transmission path and the liquid transfer or operating instrument ducts, showing the position of suitable valves. This will therefore explain how light travels through an optical fibre and show how such fibres are used in medicinal equipment either to transmit light or to bring back images from within a patient. Contents Fibre Optics Fibre-Optic Bundles Coherent and Incoherent Bundles Transmission efficiency and resolution Types of Fibres: Single mode or Multimode? Fibre Properties Fibre-Optic Endoscopy Introduction The Fibre-Optic Endoscope Some Applications for Fibre-Optic EndoscopyReferencesFibre Optics relatively new technology with vast potential importance, fibre optics, is transmission of light through hair-thin glass fibres. The clear advantages of fibre optics are too often obscured by concerns that may have been valid during the pioneering days of fibre, but that have since been answered by technical advances.

Fibre is fragile An optical fibre has greater tensile strength than copper or steel fibres of the same diameter. It is flexible, bends easily, and resists most corrosive elements that attack copper cable. Optical cables can withstand pulling forces of more than 150 pounds. Fibre is hard to work with This myth derives from the early days of fibre optic connectors. Early connectors where difficult to apply; they came with many small parts that could tax even the nimble fingered. They needed epoxy, curing, cleaving and polishing.

On top of that, the technologies of epoxy, curing, cleaving and polishing were still evolving. Today, connectors have fewer parts, the procedures for termination are well understood, and the craftsperson is aided by polishing machines and curing ovens to make the job faster and easier. Even better, epoxy less connectors eliminate the need for the messy and time-consuming application of epoxy. Polishing is an increasingly simple, straightforward process.

Pre-terminated cable assemblies also speed installation and reduce a once (but no longer) labour-intensive process. Fibre Optic Bundles If light enters the end of a solid glass rod so that the light transmitted intothe rod strikes the side of the rod at an angle O, exceeding the critical angle, then total internal reflection occurs. The light continues to be internally reflected back and forth in its passage along the rod, and it emerges from the other end with very little loss of intensity. This is the principle in fibre optics of which long glass fibres of very small cross-sectional area transmit light from end to end, even when bent, without much loss of light through their side walls.

Such fibres can then be combined into 'bundles' of dozens to thousands of fibres for the efficient conveyance of light from one (often inaccessible) point to another. If the glass fibre comes into contact with a substance of equal or higher refractive index, such as an adjacent glass fibre, dirt or grease, then total internal reflection does not occur and light is lost rapidly by transmission through the area of contact. To avoid such 'leakage' and to protect the fibres, they are clad in 'glass skins' of refractive index lower than that of the fibre core. As the angle of incidence I increases, R increases and O ( = (n/2) -R) decreases. Eventually, O reaches C, the critical angle, and any further reduction in O results in transmission through the side wall. The expression n 0 sin Imax is called the numerical aperture of the fibre.

Atypical value for this might be 0.55, making Imax about 33 o in air. Sometimes Imax is referred to as the half-angle of the fibre, since it describes half the field of view acceptably transmitted. The numerical aperture (and hence Imax) can be increased by using a core of high refractive index. However, these glasses have a lower efficiency of transmission, especially at the blue end of the spectrum, and are not commonly used. The above analysis applies only to a straight line fibre. If the fibre is curved, the angles of incidence vary as the light travels along the fibre and losses occur if the angles fall below the critical angle.

In practice, a radius of curvature down to about twenty times the fibre diameter can be tolerated without significant losses. Coherent and Incoherent Bundles An ideal fibre transmits light independently of its neighbours, so if a bundle of fibres is placed together in an orderly manner along its length, with the relative positions remaining unchanged, actual images may be transmitted along the fibre. Such an arrangement is called a coherent bundle, and consists of fibres of very small diameter about 10 um. The ends of the bundle are cut square and polished smooth to prevent distortions. Each fibre transmits a small element of the image which is seen at the other end of the coherent bundle as a mosaic. The eye has to 'look through' the fragmented structure to appreciate a clear image.

The image to be transmitted is either in direct contact with the end of the bundle or focused on to this surface. The image formed at the other end is viewed using an eyepiece incorporating magnification. One novel method of magnification is to make one end of the fibres smaller than the other. For example, if they have an average diameter of 5 um at the image end, and 50 um at the viewing end, a magnification of x 10 is achieved.

In contrast, a bundle of fibres arranged at random is known as an incoherent bundle, (or sometimes simply a light guide) and is suitable only for the transport of light not of images. The fibres of such a bundle are relatively large having diameters of about 50-100 um. The fibre, must be cabled - enclosed within a protective structure. This usually includes strength members and an outer buffer. The most common strength member is Kevlar aramid yarn, which adds mechanical strength. During and after installation, strength members provide crush resistance and handle the tensile stresses applied to the cable so that the fibre is not damaged.

Steel rods are also used as strength members in multi fibre bundles. The concentric layers of an optical fibre include the light-carrying core, the cladding and the protective buffer. Core: the inner light-carrying member. Cladding: the middle layer, which serves to confine the light to the core. Buffer: the outer layer which serves as a 'shock absorber' to protect the core and cladding from damage. The buffer protects against abrasion, oil, solvents and other contaminates.

The buffer usually defines the cable's duty and flammability rating. Transmission efficiency and resolution Light injected into a fibre can adopt any of several zigzag paths, or modes. When a large number of modes are present they may overlap, for each mode has a different velocity along the fibre (modal dispersion). The glass fibres used in present-day fibre-optic systems are based on ultrapure fused silica. Fibre made from ordinary glass is so dirty that impurities reduce signal intensity by a factor of on million in only about 5 m (16 ft) of fibre. These impurities must be removed -- often to the parts-per-billion level - before useful long-haul fibres can be drawn.

But even perfectly pure glass is not perfectly transparent. It attenuates, or weakens, light in two ways. One, occurring at shorter wavelengths, is a scattering caused by unavoidable density fluctuations within the fibre. The other is a longer wavelength absorption by atomic vibrations (photons). For silica, the minimum attenuation, or the maximum transparency, occurs in wavelengths in the near infrared, at about 1.5 micrometers. In addition, there are 'end losses' which are light losses at the end faces due to partial reflection and incidence on the cladding material.

Thus, light sources need to be very powerful, and even then problems can arise when viewing coloured images since different wavelengths have different transmission efficiencies. The thinner and more numerous the fibres, the greater should be the resolution. However, when the core diameter falls below about 5 um diffraction starts to occur and transmission efficiency drops. Hence, although fibres with core diameters down to about 1 um have been used, typical diameters are nearer 10 um. A deterioration in image quality may occur for a number of reasons, for example defects in the end faces of the fibres, misalignment of fibres, broken fibres (causing black spots), or light leakage between adjacent fibres (producing " cross-talk'). Types of fibres: Singlemode or Multimode?

In the simplest optical fibre, the relatively large core has uniform optical properties. Termed a step-index multi mode fibre, this fibre supports thousands of modes and offers the highest dispersion - and hence the lowest bandwidth. By varying the optical properties of the core, the graded-index multi mode fibre reduces dispersion and increases bandwidth. Grading makes light following longer paths travel slightly faster than light following a shorter path. Put another way, light travelling straight down the core without reflecting travels slowest.

The net result is that the light does not spread out nearly as much. Nearly fibres used in medical application have a graded index. Fibre Properties Numerical aperture (NA) of the fibre defines which light will be propagated and will not. NA defines the light-gathering ability of the fibre. Imagine a cone coming from the core. Light entering the core from within this cone will be propagated by total internal reflection.

Light entering from outside the cone will not be propagated. NA has an important consequence. A large NA makes it easier to inject more light into a fibre, while a small NA tends to give the fibre a higher bandwidth. Large NA allows greater modal dispersion by allowing more modes in which light can travel. A smaller NA reduces dispersion by limiting the number of modes. Fibre-optic endoscopy Introduction An endoscope is an instrument designed to provide a direct view of an internal part of the body, and possibly to perform tasks such as the removal of samples, injection of fluids and diathermy.

Fibre optics has extended the scope of the instrument considerably by permitting the transmission of images from inaccessible areas such as the oesophagus, stomach, intestines, heart and lungs. The fibre-optic endoscope The long flexible shaft of the instrument is usually constructed of steel mesh, often with a crush-resistant covering of a bronze or steel spiral, it is then sheathed with a protective, low-friction covering of PVC or some other impervious material, which forms a hermetic seal around the instrument. The shaft is about 10 mm in diameter; about 0.6-1.8 m long (depending on the application) and has a short deflectable section about 50-85 mm long leading to its distal tip. Within the shaft lie: (a) at least one non-coherent fibre-optic bundle to transmit light from the distant light source to the distal tip; (b) a coherent fibre-optic bundle transmitting the image from the objective lens at the distal tip; (c) an irrigation channel through which water can be pumped to wash the objective lens; (d) an operations channel for the Performance of tasks; (e) control cables. The viewing end of the endoscope contains: (a) an eyepiece, with focus controls and camera attachment; (b) distal tip deflection controls, giving poly directional control up to about 200 o, plus locking capability; (c) objective lens control which may be a push-pull wire effecting focusing; (d) valve controls for air aspiration, (suctioned withdrawal of body fluids through the operations channel) and lens washing and air insufflation (application of water or air jet through the irrigation channel); (d) operating channel valve, which controls the entry of catheters, electrodes, biopsy forceps and other flexible devices; (e) connection with the umbilical tube, providing light through a non-coherent fibre-optic bundle and water or air from the pump or aspirator system.

A typical Micro-video Endoscopy Unit would contain: (a) Optical catheter system as described above, (b) Colour video monitor (c) CO 2 and fluid insufflation, (d) Instrumentation, (e) Disposables, (f) Miscellaneous accessories. Some applications of Fibre-optic endoscopy Endoscopic examination of the gastrointestinal tract has proved especially successful with the diagnosis and treatment of ulcers, cancers, constrictions, bleeding sites, and so on. The heart, respiratory system and pancreas have also been investigated. Another application is the measurement of the proportion of haemoglobin in the blood which is combined with oxygen using an oxime ter. Two incoherent bundles are introduced into the blood stream: one is used to illuminate a sample of blood and the other to assess the absorption of light by the blood. An endoscope can also be equipped with a laser that can vaporize, coagulate, or cut structures, often with more ease and flexibility than a more rigid cutting knife.

It is a less invasive method that causes less scarring and a quicker recovery time than other surgical techniques. Common types of endoscopes are the cystoscope to view the bladder, the bronchoscope to view the lungs, the otoscope to view the ear, the arthroscope to view the knee and other joints, and the laparoscope to view the female reproductive structures. The most common surgery performed through endoscopy is biopsy, the removal of tissue for microscopic study to detect a malignancy. Diagnostic with directed biopsy and dilatation and curettage, removal of polyps, and removal of foreign objects and Cystourethroscopy are other important fields which endoscopy makes possible.

Bibliography

Pope, Jean A. ; Medical Physics 2nd r. e. Heinemann Educational Printers 1973.
Brown, B.H., Smallwood R.H. ; Medical Physics and Physiological Measurement; Blackwell Scientific Publications, Billing and Son's Publishers; 1981.